Country Tractor & Equipment

Information

Case IH DC105 CENTER-PIVOT DISC MOWER CONDITIONER – Stock # C014F

Glide through lush stands of alfalfa, acres of dense grass and even tough cane crops, at high ground speeds.

CLEANER, CLOSER CUT
• The low-profile cutterbar and wide discs cut closer and cleaner, promoting faster, healthier crop regrowth.
• More counter-rotating discs provide efficient crop feeding into the conditioners.
• Reduced crop travel between cutterbar and conditioners minimizes plugging.

VERSATILITY
• Fine-tune your cutting based on crop conditions by easily adjusting windrow-forming shields, swathgate, cutting height and conditioning roll pressure without tools.
• Heavy-duty, quick-change knives cut change time in half and are reversible for double the cutting life.

DURABILITY
• The fully encased modular design provides superior hillside lubrication and contains any system failures due to no free-flowing oil between each module.
• Each module is protected from damage by an external shear hub located under the disc and on top of the module.

Cutterbar
Cutting Width: 10 ft. 1 in. (3 072 mm)
Cutting Height: 0.79 – 2.7 in. (20 – 69 mm)
Cutting Height w/ Optional High-Stubble Shoes: 3.1 – 5.5 in. (79 –140 mm)
Cutterbar: Modular
Number of Discs/ Knives: 6 / 2
Disc Speed at 1,000 PTO: 2,250 RPM^
Module Protection: Shock hub system
Shock hub system: 2 – 10º
Cutterbar Tilt System: 4-position hydraulic cylinder
Cutterbar Shear Protection: Standard– frangible splines in disc drive hub
CROP CONDITIONING
Cutterbar Flotation: Vertical and lateral, adjustable springs
Type: Chevron intermeshing molded rubber
Length /Diameter: 90 in. (2 286 mm)/ 10.4 in. (264 mm)
Diameter: 2×10.4 in. (264 mm) rolls
Roll Drive: 4 HB V-belt & enclosed gears
Roll Speed: 640 / 750 RPM
Roll Tension Adjustment: Single crank
Conditioner Gap Adjustment: Single crank adjustment of rotor hood
Swath Width: 6 ft. (1.8 m)
Windrow Width: 3 – 8 ft. (0.9 – 2.4 m

DRIVELINE
Input Speed: 540 RPM or 1,000 RPM
Driveline Protection: Slip clutch and overrunning clutch assembly @ rear of PTO shaft

TRACTOR REQUIREMENTS
Minimum PTO HP Required: 80
PTO Shaft Spline/ Size Requirements: 6-spline/ 1 3/8 or 21-spline/ 1 3/8
Hydraulic Remotes Required: 2
Minimum Relief Pressure: 1,500 psi (103 bar)
Drawbar/ Swivel Hitch-Drawbar/ Swivel Hitch- 2-pt.: ASAE Cat. 2 or 3 drawbar or Cat. 3 3-pt. hitch
Electrical: 7-pin electrical connector for transport lights

DIMENSIONS* & WEIGHTS**
Operating Length: 23 ft. 7 in. (7.2 m) w/ 2-pt. hitch; 22 ft. 8 in. (6.9 m) w/ drawbar hitch
Operating Height: 6 ft. 7 in (2.0 m)
Transport Length: 2pt swivel hitch 27 ft. 5 in. (8.4m) drawbar swivel hitch 26 ft. 5 in. (8.1m)
Transport Width: 10 ft. 1 in. (3 072 mm)
Transport Height: 7 ft. 5 in. (2.26 m)
Transport Speed (mph /kph): 20 mph (32)
Ground Clearance When Fully Raised: 16.2 in. (411 mm)
Operating Weight: Flail: 5,660 lb. (2 567 kg) / Roll: 5,760 lb. (2 613 kg)
Tires: 12.5L×15.8 PR

3 YEAR CUTTERBAR FACTORY WARRANTY