2022 Case IH DC93_MWR COND STD RUBBER

SIDE-PULL DISC MOWER CONDITIONERS - DC93 (ROLL)

CLEANER, CLOSER CUT
• The low-profile cutterbar and wide discs cut closer and cleaner, promoting faster, healthier crop regrowth.
• More counter-rotating discs provide efficient crop feeding into the conditioners.
• Reduced crop travel between cutterbar and conditioners to minimize plugging.

VERSATILITY
• Fine-tune your cutting based on crop conditions by easily adjusting windrow-forming shields, swathgate, cutting height and conditioning roll pressure without using tools.
• Heavy-duty, quick-change knives cut change time in half and are reversible for double the cutting life

DURABILITY
• The fully encased modular design provides superior hillside lubrication and contains any system failures due to no free-flowing oil between each module.
• Each module is protected from damage by an external shear hub located under the disc and on top of the module

RUBBER ON RUBBER
• For thorough conditioning of leafy crops; provides full-stem crimping and cracking while delicately handling the leaves.
• Constructed with high-wear rubber for years of life

EASY ADJUSTMENTS
• The torsion-bar’s roll-pressure design applies equal force to the conditioning rolls for greater consistency and less strain on the machine.
• The torsion-bar design has a single point of adjustment to fine-tune the roll pressure.
• Several systems on the disc mower conditioners can be adjusted without tools, adapting to current crop conditions and producing the highest-quality hay possible, including:
• Windrow Formation — Swathgate and forming shields are easily adjusted without tools; spread wide or narrow to fit your needs
• Conditioning Roll Pressure — A single point of adjustment fine-tunes the roll pressure
• Knife Maintenance — Easy access allows you to change the quick-change knives in seconds
• Cutting Height — Repositioning a pin in the hydraulic tilt cylinder changes the cutting heigh

CUTTERBAR:
Cutting Width: 9 ft. 2 in. (2.8 m)
Cutting Height: 1.1 – 2.7 in. (29 – 68 mm)
Cutting Height w/ Optional High-Stubble Shoes: 2.25 – 4.5 in. (58 – 115 mm)
Cutting Height w/ Optional High-Stubble Shoe: 2.25 – 4.5 in. (58 – 115 mm)
Cutterbar: Modular
Number of Discs/ Knives: 7 / 2
Disc Speed at 540 PTO: 3000 rpm*
Module Protection: Shock hub system
Cutterbar Tilt Angle: 2-10”
Cutterbar Tilt System: 4-position hydraulic cylinder
Cutterbar Shear Protection: 3,000 rpm

CROP CONDITIONING
Cutterbar Flotation: Vertical and lateral, adjustable springs
Type: Chevron rubber rolls
Length: 90 in. (2 286 mm)
Diameter: 10.4 in. (264 mm)
Roll Drive: 4 HB V-belt and enclosed gear
Roll Speed: 647 rpm
Adjustments: Hand crank; No tools required
Swath Width: 6 ft. (1.83 m)
Windrow Width: 3 – 6 ft. (0.9 – 1.83 m)

DRIVELINE
Input Speed: 540 rpm
Driveline Protection: Slip clutch and overrunning clutch assembly at rear of PTO shaft

TONGUE & HITCH OPTIONS
Tongue Style: Straight tongue
Hitch Options: Standard clevis

TRACTOR REQUIREMENTS
Minimum PTO HP Required: 65
PTO Shaft Spline/ Size Requirements: 540, 1.375 in. 6-spline
Hydraulic Remotes Required: 2
Minimum Relief Pressure: 1500 psi
Drawbar/ Swivel Hitch-Drawbar/ Swivel Hitch- 2-pt.: ASAE Cat 2
Electrical: 7-pin electrical connector for transport lights

DIMENSIONS* & WEIGHTS
Operating Width (Standard): 14 ft. 10 in. (4.52 m)
Operating Length: Roll: 17 ft. 2 in. (5.23 m)
Operating Height: 4 ft. 5 in. (1.35 m)
Transport Length: Roll: 17 ft. 7 in. (5.36 m)
Transport Height: 5 ft. 8 in. (1.73 m)
Transport Speed (mph/kph): 18 mph (32)
Ground Clearance When Fully Raised: 17 in. (432 mm)
Operating Weight: Roll: 3,740 lb. (1 697 kg)
Tires: 9.5L×14L 6PR


3 YEAR CUTTERBAR FACTORY WARRANTY